Sale!
 

High Voltage Red Simon K NFet Esc simonk esc 12a for quadcopter

$15.50 $8.50

These are fantastic multi rotor ESCs.  They are recommended on any 12 amp setup.   They are High voltage and designed to work with 2s to 4s batteries.

 

These ESCs will give your multi rotor quicker reflexes, less drift, and smoother flights. ALL ESCs are flashed with the most current version of the famous SimonK firmware.

In stock

SKU: HVRSKNEse1fq Category: Tag: Brand:
 

Description

simonk esc 12a for quadcopter

These work well with 4S batteries and 2000KV motors.

Specifications

  • Continuous: 12 Amp
  • Burst: 16 Amp
  • Atmel processor
  • All N-FETS
  • Battery: 2-4S Lipoly
  • SBEC: NONE
  • 22x40x8mm
 

Simply put, one of the best ESCs you can get for your multi rotor. simonk esc 12a for quadcopter

 

These escs are a little long for the QAV250, and thus will stick past the PDB a bit.

  • All N-channel FETs
  • External Oscillator:
  • Boot-loaded Enabled

Flashed with the famous SimonK OpenSource Firmware for super-fast throttle response, which makes your quad more responsive and “locked in”.  These  ESCs do not overheat, burn or lock out – unline many other ESCs flashed with the SimonK firmware.

These ESCs are completely re-designed from the ground up. Flashed with the famous SimonK OpenSource Firmware for better throttle response . New firmware means direct, linear throttle response, making it suitable for multicopter use. Up to 600Hz input rate is supported, with immediate updates to motor pwm duty. Each ESC is tested with a motor before and after loading new firmware.

The the external 16MHz oscillator line up exactly with the numbers in microseconds, but the internal rc oscillator ones will drift quite a bit based on temperature.

The ESCs use only N-channel FETs have the advantage of lower resistance, less losses and hence more efficiency.

All N-Fet:”The ESCs which use only N-channel FETs have the advantage of lower resistance, less losses and hence more efficiency.”*

External Oscillator:”An external oscillator may supply a more consistent timing signal and steadier motor speeds” “but the internal rc oscillator ones will drift quite a bit based on temperature.

These ESCs are a revision of the nearly-perfect F20A & F-30A ESCs with high quality board layout and components to make them perfect. Do not settle for anything less.

NOTE: This firmware does NOT check battery voltage or ESC temperature. Always use a LiPo alarm and monitor pack voltage while using.

NOTE: These are not I2C ESCs and as such are not directly compatible with Mikrokopter-style interface, however they can be used with I2CPWM converter

Additional information

Weight 0.1 lbs
Dimensions 1 x 1 x 1 in

Share your thoughts!

Let us know what you think...

What others are saying

  1. james e williamson

    Question

    james e williamson

    could i get this with a custom firmware loaded..or can you suggest a esc that would be compatible
    https://github.com/seandepagnier/brushed_tgy

    (0) (0)

    Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

    • Anthony Jacobs

      QQTeam Anthony Jacobs

      Why run brushed motors on your drone when you can run brushless motors? there are so many great advantages, especially when it comes to performance on smaller quadcopter such as tiny whoop builds. You are re-inventing the wheel when there is an obvious advantage to brushless motor use in mulit-rotors vs. brushed from an engineering standpoint. Sure, we could flash custom ESCs for you at QQ, but we would rather help you build the most efficient, fastest, and best flying drone possible.

      (0) (0)

      Something wrong with this post? Thanks for letting us know. If you can point us in the right direction...

×

Continue as a Guest

Don't have an account? Sign Up