NerdSense OSD for the Nerdcam3D camera

$49.99

Use this board to get OSD on a Nerdcam3d 3d FPV camera.

When flying FPV, a good OSD is essential.  The Nerdsense board makes the challenges of 3D OSD and makes them easy!  Normal OSDs are not made to work in sync with 2 pictures, and can cause very undesirable results.  This board makes it very easy to sense voltage, current, RSSI, time, current over time and more!

One wire installation between the OSD Sensing board and the camera and you are in business.

Out of stock

Sold Out

SKU: NOftNc Category: Tag: Brand:
 

Description

The NerdSense OSD Mk.1- The OSD for the NERDCAM3D

The NerdSense OSD Mk.1 sensor board is the OSD required to get the most out of the Nerdcam3d‘s built-in stereoscopic OSD. The sensor basically measures voltage, current consumption as well as your RC-receiver’s RSSI output signal and prepares these data for the 3D-camera. Out of this raw information the camera generates the stereoscopic OSD covering voltage (0 to 25.5V), current draw (0 to 100A), charge counter (0 to 9999 mAh), wall-clock (0 to 60 min) and RSSI bar display.

 

Connect the sensor with the accompanying cable to the camera and the camera’s OSD becomes activated automatically upon camera start-up. Use either PWM-RSSI or DC-RSSI raw signals from different RC-receivers with user-defined 0% and 100% RSSI thresholds. If RSSI is not necessary for your application, simply deactivate it with the sensor’s on-board controls. Enjoy integrated RSSI signal conditioning with RC-filtering and user-defined amplification.

 

This is how the stereoscopic OSD will look like for side-by-side 3D-mode. The complete information block is embedded twice into the video stream without introducing any latency. Notice the inwards offset of left and right block. This offset is necessary for the optimal 3D-convergence setting. The chosen offset value defines the virtual distance in which the OSD will float in front of you. The offset can be adjusted with the camera’s trim potentiometer for best user experience. All these features are available for the alternative field-sequential 3D mode as well without any limitation.

Attach the sensor to your camera and the other devices of your RC-vehicle like shown in this wiring diagram. Notice the safety advice.

The NerdSense Mk.1 sensor will work with any firmware version of the NerdCam3D, however the number of displayed parameters is dependent on the actual firmware version. The following table summarizes those firmware versions currently in use and explains which OSD parameters are supported respectively.

Type and Serial Number

FW-Version

OSD Parameters
NerdCam3D Mk.1 up to S/N 1096  2.1 Voltage, Current consumption, Time
NerdCam3D Mk.1 starting with S/N 1097 2.3 Voltage, Current consumption, Time, mAh Counter and RSSI
Updated NerdCam3D Mk.1 devices with S/N: 1003, 1010, 1021, 1026, 1038, 1046, 1058, 1062, 1069, 1074, 1076, 1077 2.3 Voltage, Current consumption, Time, mAh Counter and RSSI

 

Any NerdCam3D 3D-camera with firmware version 2.1 can be updated with a newer firmware. For this, the 3D-camera must be sent to the manufacturer. If interested please contact us to arrange a firmware update. Updating the camera via the reseller network is unfortunately not possible at the moment.

Instruction Manuals

Download
NerdSense Mk.1 – Instruction Manual (English)
NerdSenseMk1_InstructionManual.pdf
Adobe Acrobat Document [721.7 KB]
Download
Download
NerdSense Mk.1 – Gebrauchsanweisung (German)
NerdSenseMk1_Gebrauchsanweisung.pdf
Adobe Acrobat Document [688.5 KB]
Download

Technical Remarks on RSSI Signal Sources

General Notice for DC-RSSI Signals

The RC-receiver’s output voltage for 0% RSSI must be lower than the voltage corresponding to 100% RSSI. Please note the permitted voltage range of 0V to 3.3V DC at the RSSI input of the sensor in DC-RSSI mode.

General Notice for For PWM-RSSI Signals

The pulse width of the RC-receiver’s RSSI signal for 0% RSSI must be lower than the corresponding pulse width for 100% RSSI. Please note the maximum PWM signal magnitude of 5V DC at the RSSI input of the sensor in PWM-RSSI mode.

Special Notice on EzUHF RC-Receivers

EzUHF receivers provide both RSSI and Link Quality (LQ) signals, both as PWM-signals. Unfortunately only the LQ signal is compliant with the corresponding general notice above (http://diydrones.com/xn/detail/705844:Comment:1669593). There are additional 3rd-party devices available which convert EzUHF’s inverted RSSI raw signal into a DC-RSSI signal:

a) http://fpvlab.com/forums/showthread.php?22152-Digital-to-Analog-Converter-%28For-EzUHF-RSSI-amp-Link-Quality%29

b) http://www.sis-labs.com/products/rssi-dax/

Special Notice on Futaba® FASST™ RC-Receivers

The tapping of the RSSI signal from Futuba® FASST™ receivers has been described elsewhere (http://blog.flytron.com/rssi-output-for-2-4ghz-futaba-fasst.html or http://fpv-community.de/showthread.php?7271-Futaba-R617FS-RSSI-Signal). You only need to attach the wires as described in Flytron’s blog on the RC-receiver. The mentioned SMD RC-filter is not necessary, as the NerdSense provides its own. Connect this raw signal to the RSSI-input of the NerdSense and don’t forget to put it into PWM-mode. Then proceed with the RSSI calibration as outlined in the manual.

Additional information

Weight 0.1 lbs
Dimensions 3 × 3 × 1 in

Reviews

There are no reviews yet.

Be the first to review “NerdSense OSD for the Nerdcam3D camera”

Your email address will not be published. Required fields are marked *